PA 12 nylon properties explained: strength, heat and chemical resistance
What PA 12 nylon from HP Multi Jet Fusion can take: strength by build direction, heat, moisture, oils, fuels and skin contact, and where its limits sit.
PA 12 is a tough, fairly stiff nylon that shrugs off oils, greases, fuels and alkalis, absorbs very little water and keeps its shape in humid air. Its limits are heat under load and some aggressive solvents and acids, so check those two before you commit a part to it.
This guide explains what each property means for a real part made on HP Multi Jet Fusion (MJF), where the published figures come from, and how far you can trust them. If you are new to the process itself, start with our plain guide to HP Multi Jet Fusion.
What PA 12 is and why it suits 3D printing
Polyamide 12 belongs to the nylon family. Compared with the more common PA 6 and PA 66, its molecules have longer carbon chains between the amide groups. A 2025 review in Polymers explains that these longer chains reduce the density of hydrogen bonds, which makes PA 12 more flexible and far less thirsty for water than PA 6.
Evonik, which makes PA 12 under the VESTAMID name, describes its PA 12 grades as having very low water absorption, high dimensional stability and good impact strength even in the cold. Those are the same reasons PA 12 is used for fuel lines, cable sheathing and catheters, well outside 3D printing.
For powder bed printing, PA 12 has another advantage: a low melting point for a nylon. The RMIT study of HP's PA 12 lists the powder's melting point as 187 °C and the printed part density as 1.01 g/cm³, which makes PA 12 parts light, just above the density of water.
Strength and stiffness, and why build direction matters
Our PA 12 material page lists typical values for MJF parts of about 48 MPa tensile strength and about 20% elongation at break, with a part density of 1.01 g/cm³. In practice that means a part that bends and yields before it snaps, which is why PA 12 works for snap-fits, clips and living hinges where brittle plastics crack.
Two points matter when you use these numbers in a calculation.
- Build direction changes the result. MJF parts are close to equal in every direction, but not exactly. Lee and Kajtaz (2022) found that horizontally printed tensile bars were about 40% lower in stiffness and about 20% lower in strength than bars printed at 45°. Perez-Barcenilla and colleagues (2024) found vertical specimens about 16% higher in strength and modulus than flat ones, while elongation at break tends to fall in the vertical direction.
- Published figures are a best case. The 2024 study notes that results across independent research tend to come in lower than HP's own published values. Print mode, powder refresh ratio, part thickness and test method all move the numbers.
The working rule: design with a safety margin on the datasheet value, and tell your supplier which direction takes the load so the part can be oriented for it.
Heat resistance: what the heat deflection figure means
The PA 12 page on our site gives a heat deflection temperature of about 175 °C at 0.45 MPa. That figure is easy to misread.
Heat deflection temperature is measured by heating a standard bar under a small fixed load and noting when it bends a set amount. At 0.45 MPa the load is light, so the result sits close to the melting point. A real bracket carrying a steady load, or a housing next to an engine for hours, will start to creep well below that temperature. Many datasheets also give a value at the higher 1.82 MPa load, and that figure is the better guide for loaded parts.
For heat, a sensible approach is:
- Use the 0.45 MPa figure only for lightly loaded parts such as covers and ducts.
- For parts under constant load in hot places, prototype and test at the real temperature and load.
- Remember that PA 12 melts at around 187 °C, so it is not a choice for parts that touch exhaust or hot metal directly.
Moisture and dimensional stability
Many nylons swell and soften as they take up water from the air. PA 6 is known for this. PA 12 is much less affected.
A 2021 study from Universidad Carlos III de Madrid measured water uptake on hot-pressed PA 11 and PA 12 under ASTM D570. Uptake levelled off at about 1.5% by weight when fully immersed in water and about 0.8% at 23 °C and 50% relative humidity, over roughly two months. The authors report that the absorbed water did not plasticise the material, and that neither hardness nor dimensions changed. Printed parts have a slightly different, more porous structure than pressed sheets, so treat these numbers as a guide, not a guarantee.
For buyers in India, this matters in monsoon months and coastal sites. A PA 12 part that fits in a dry lab in winter will still fit in July, which is not always true of PA 6 parts.
HP also states that its PA 12 achieves watertight properties without extra post-processing. That helps for fluid housings and enclosures, but pressure-test any part that has to hold liquid or gas before it goes into service.
Chemical resistance: what PA 12 handles and what to test
HP's material entry describes PA 12 as having excellent chemical resistance to oils, greases, aliphatic hydrocarbons and alkalis. Evonik adds fuels, hydraulic fluids and many solvents to that list for its PA 12 grades. This is why Evonik lists automotive fluid lines among the main uses of PA 12.
| Exposure | What the sources say | What to do |
|---|---|---|
| Engine oil, grease, hydraulic fluid | Excellent resistance (HP, Evonik) | Suitable for most parts |
| Petrol, diesel, aliphatic hydrocarbons | Strong resistance (HP, Evonik) | Suitable; test seals and thin walls |
| Alkalis and cleaning solutions | Excellent resistance (HP) | Suitable for most parts |
| Strong acids, chlorinated or aromatic solvents | Not covered by HP's claim | Test on a sample before use |
| Food and drink | Not approved (HP, 2021) | Do not use for food contact |
The safe habit is simple: if a chemical is not on the list above, soak a sample part in it at working temperature and check weight, size and stiffness afterwards.
Skin contact, food contact and regulated uses
HP states that its PA 12 meets USP Class I-VI and US FDA guidance for intact skin surface devices, and its regulatory summary reports passing ISO 10993 tests for cytotoxicity, sensitisation and irritation. HP also says it cannot guarantee that the material will meet these standards for any particular use, so the device maker remains responsible for its own validation.
Food contact is a firm no. HP's regulatory summary says no HP 3D materials are designed or approved for direct or indirect food contact.
For automotive work, HP's materials page notes that PA 12 meets US Federal Motor Vehicle Safety Standards. For defence and aerospace buyers, the material is only part of the story: batch records and inspection under a quality system matter as much. Pranava Fusion is certified to AS9100D and ISO 9001:2015.
To check a design, upload your STEP or STL file on our quote page. We review every file and reply within 1 to 5 hours on working days, and parts are printed on HP Multi Jet Fusion at our unit in Ibrahimpatnam, Hyderabad.
Frequently asked questions
Is PA 12 the same as nylon 12? Yes. PA stands for polyamide, the chemical name for nylon, and 12 refers to the number of carbon atoms in its repeating unit.
How strong is MJF PA 12? Our material page lists about 48 MPa tensile strength and about 20% elongation at break. Independent studies often measure somewhat lower values, and results change by up to tens of percent with build direction, so design with a margin.
Can PA 12 parts be used outdoors or in humid places? Humidity is not a problem: PA 12 takes up little water and holds its size. For long sun exposure, test a sample first, because the sources here give no UV ageing data.
What temperature can PA 12 parts take? Lightly loaded parts cope with high temperatures, as the 175 °C heat deflection figure at 0.45 MPa shows. Parts under steady load creep at much lower temperatures, so test loaded parts at their real working temperature.
Is PA 12 safe for food? No. HP does not approve its 3D printing materials for direct or indirect food contact.
Sources
- HP 3D printing materials portfolio (HP, 2026)
- HP 3D High Reusability PA 12 material entry (UL Prospector, supplied by HP)
- HP 3D HR PA12: summary of regulatory compliance and environmental attributes (HP, 2021)
- Experimental characterisation and finite element modelling of polyamide-12 fabricated via Multi Jet Fusion (Lee and Kajtaz, Polymers, 2022)
- A transversely isotropic material model for Multi Jet Fusion printed polyamide 12 parts (Perez-Barcenilla et al., Polymers, 2024)
- Comparative characterization of hot-pressed polyamide 11 and 12 (Bahrami, Abenojar and Martínez, Polymers, 2021)
- Review of pure and reinforced polyamide 6 and polyamide 12 materials (Kohutiar et al., Polymers, 2025)
- VESTAMID polyamides (Evonik)